*** UNIX MANUAL PAGE BROWSER ***

latsetup(8) System Manager's Manual latsetup(8) NAME latsetup - Local Area Transport (LAT) setup utility SYNOPSIS /usr/sbin/latsetup [-nocurses] FLAGS Specifies that latsetup is run in noncurses and nonmenu-driven mode. Use this option if the terminal you are using does not support curses. Note that using the latsetup command with the -nocurses option provides limited functionality. DESCRIPTION The latsetup command provides an interactive, menu-driven facility for administrating LAT on your system. (For introductory information on LAT, see the lat_intro(7) reference page.) To use latsetup, LAT must be built into the running kernel, your system must be at run level 3 or 4, and you must be logged in as superuser. For more information, see the Network Administration manual. Note Running multiple latsetup processes concurrently on the same machine can cause erroneous information to be presented to the latsetup user and can corrupt the /etc/inittab file. You can use the latsetup utility to perform the following tasks: Do initial LAT setup Create LAT device special files Add or delete getty entries to or from the /etc/inittab file Execute init q Start or stop the LAT driver Enable or disable LAT automatic startup and shutdown If LAT is not configured into the running kernel, latsetup only allows you to remove the LAT entries from the /etc/inittab file. If you enable LAT automatic startup and shutdown, the /sbin/init.d/lat script starts LAT upon reaching run level 3 and stops LAT upon leaving run level 3. To run latsetup, log in as superuser and enter the following command: # /usr/sbin/latsetup In the device creation phase, you choose to create SVR4-style or BSD- style devices. (For an explanation of the types of devices, see the Network Administration manual.) A maximum of 620 BSD-style devices is supported. Digital recommends the use of SVR4-style devices. If you need a large number of devices, Digital recommends you use SVR4-style devices. If you create SVR4 devices using latsetup, and an SVR4 device was mapped as an application port and the device was removed, the port (or service) information remains associated with the minor number corre- sponding to the device that was removed. Therefore, when latsetup cre- ates more devices, it may create the device that was mapped as an ap- plication port (if the device name is within the range of SVR4 devices being created). The latsetup utility does not add a getty entry for the device in the /etc/inittab file. This device is not counted as a newly created SVR4 device, because it is already being used as an ap- plication port. If you delete SVR4 devices using latsetup, and an SVR4 device was mapped as an application port and has an associated getty entry in the inittab file, if the device name is within the range of SVR4 devices being removed, latsetup removes the associated getty entry in the /etc/inittab file. When removing SVR4 devices, latsetup does not re- move the device, because it is mapped as an application port. This de- vice is not counted as an SVR4 device that has been removed. The lat- setup utility creates device names that directly correspond to minor numbers (for example, SVR4 device /dev/lat/620 corresponds to minor number 620). Customization After you run latsetup, you can customize your system's LAT environment by modifying the following files: /etc/inittab Edit the /etc/inittab file to add any LAT entries. For example, you can add an entry for the LAT/Telnet gateway. For more in- formation refer to the guide to Network Administration and init- tab(4). Note If you delete entries in the /etc/inittab file and then run lat- setup to make other changes or deletions, latsetup might not be able to complete successfully. /sbin/latstartup.conf Create and modify the /etc/latstartup.conf file to include latcp commands to customize your LAT system. This file is read by the /sbin/init.d/lat script, which executes the commands included in the file. For example, you can change the LAT node name or add additional service names. For more information refer to the guide to Network Administration and latcp(8). FILES Specifies the BSD LAT terminal devices. (Where W is a number from 0 to 9 and X is an alphanumeric character from 0 to 9, a lowercase a to z, or an uppercase A to Z.) LAT supports up to 620 BSD LAT terminal de- vices. Specifies the SVR4 LAT device special files. (Where n is a number starting at 620 and having no upper limit.) Specifies the LAT control device. Specifies the LAT startup and shutdown script. Speci- fies LAT customization commands. Sets up the system database to auto- matically push the ldterm STREAMS module on top of the LAT STREAMS dri- ver each time a LAT tty is opened. Controls the initialization process. Specifies the system configuration file. RELATED INFORMATION Commands: llogin(1), init(8), latcp(8), MAKEDEV(8), strsetup(8). Files: inittab(4). Introduction: lat_intro(7), lat_manual_setup(7). Network Administration delim off latsetup(8)